lan карта
2 отговора
0 прегледа
lan карта
възможно ли е и ако да как се включва картата на 10М/100м /знам че си я детектва автоматично но може ли ръчно да се зададе скороста./ примерно искам да пусна нет на приятел които е далеч/400 м слагам VLAN SW но трябва и ланката да ми е на 10М .линк нещо или команда.с ФЕДОРА 4 съм 2.6.17.1 лан карата е риалтек ?
Re: lan карта
man ifconfig
/*
media type
Set the physical port or medium type to be used by the device.
Not all devices can change this setting, and those that can vary
in what values they support. Typical values for type are
10base2 (thin Ethernet), 10baseT (twisted-pair 10Mbps Ethernet),
AUI (external transceiver) and so on. The special medium type
of auto can be used to tell the driver to auto-sense the media.
Again, not all drivers can do this.
*/
man mii-tool
/*
Most intelligent network devices use an autonegotiation protocol to
communicate what media technologies they support, and then select the
fastest mutually supported media technology. The -A or --advertise
options can be used to tell the MII to only advertise a subset of its
capabilities. Some passive devices, such as single-speed hubs, are
unable to autonegotiate. To handle such devices, the MII protocol also
allows for establishing a link by simply detecting either a 10baseT or
100baseT link beat. The -F or --force options can be used to force the
MII to operate in one mode, instead of autonegotiating. The -A and -F
options are mutually exclusive.
*/
man ethtool
/*
-s option allows changing some or all settings of the specified
ethernet device. All following options only apply if -s was
specified.
speed 10|100|1000
Set speed in Mb/s. ethtool with single argument will show you
the supported device speeds.
duplex half|full
Set full or half duplex mode.
port tp|aui|bnc|mii
Select device port.
autoneg on|off
Specify if autonegotiation is enabled. In the usual case it is,
but might cause some problems with some network devices, so you
can turn it off.
*/
Дишайте лепило - хиляди GNU/Linux юзери не могат да грешат !
DrFrancky
/*
media type
Set the physical port or medium type to be used by the device.
Not all devices can change this setting, and those that can vary
in what values they support. Typical values for type are
10base2 (thin Ethernet), 10baseT (twisted-pair 10Mbps Ethernet),
AUI (external transceiver) and so on. The special medium type
of auto can be used to tell the driver to auto-sense the media.
Again, not all drivers can do this.
*/
man mii-tool
/*
Most intelligent network devices use an autonegotiation protocol to
communicate what media technologies they support, and then select the
fastest mutually supported media technology. The -A or --advertise
options can be used to tell the MII to only advertise a subset of its
capabilities. Some passive devices, such as single-speed hubs, are
unable to autonegotiate. To handle such devices, the MII protocol also
allows for establishing a link by simply detecting either a 10baseT or
100baseT link beat. The -F or --force options can be used to force the
MII to operate in one mode, instead of autonegotiating. The -A and -F
options are mutually exclusive.
*/
man ethtool
/*
-s option allows changing some or all settings of the specified
ethernet device. All following options only apply if -s was
specified.
speed 10|100|1000
Set speed in Mb/s. ethtool with single argument will show you
the supported device speeds.
duplex half|full
Set full or half duplex mode.
port tp|aui|bnc|mii
Select device port.
autoneg on|off
Specify if autonegotiation is enabled. In the usual case it is,
but might cause some problems with some network devices, so you
can turn it off.
*/
Дишайте лепило - хиляди GNU/Linux юзери не могат да грешат !
DrFrancky